High Dynamic Range(HDR) Display
The OBM series supports display of High Dynamic Range footage.
Postium HDR function allows users to view both highlights and shadow details of scenes at the same time, allowing users to achieve more natural and realistic images.
The OBM series supports PQ EOTF (SMPTE ST 2084), Hybrid Log Gamma and S-Log3.

OBM-HDRdisplays both HDR and SDR(Standard Dynamic Range) versions of the image simultaneously for easy comparison.


Fast Mode
This function minimizes the interlaced video processing time delay and is also useful when displaying fast-motion interlaced video content and when reducing the delay between video and audio.

Internal Video Processing Time


Focus Assist
This function controls the aperture level of a video signal and displays images on screen with sharpened edges to help camera focus operation.


False Color
This function evaluates the Luma(Y’) level of the input image. If a certain Y’ level is set, the pixels with the designated Luma(Y’) level are displayed with the zebra pattern or the color pattern. Below are the three available modes in OBM False Color.


Adjustable Gamma
Gamma value can be adjusted to any value between 1.0 to 3.0 based on the user’s preference to monitor the dark areas of the picture.
This function enables any pictures taken in either light or dark environment can be easily viewed or analyzed.


Camera Log Selection
The OBM series has the integrated camera LUT of the various camera manufacturers. It allows users to load the following camera logs.
Log-C, C-Log / S-Log2, S-Log3 / J-Log1 The more camera LUTs will be updated.


Camera Log Mapped SDI Loopout
This function allows loading of the camera log to the original image so that the camera log mapped image can be sent to another monitor through an SDI loop out.


Remote Control via Ethernet
The OBM series can be connected via Ethernet connection and controlled remotely on the network.


Closed Caption
The OBM series can display closed captions with an SDI input. It supports the CEA-708(HD-SDI closed captioning standard) and CEA-608(SD-SDI closed captioning standard).


Waveform & Vector Scope Position Changeable
The position of Waveform and Vector Scope can be changed to all four corners of the screen.


Waveform & Vector Scope Size Adjustable
The image size of Waveform and Vector Scope can be set to Small or Large.


System Data Copy
This function allows users to save their monitor configuration and adjustment settings on a USB memory stick and load them to other monitors. This is useful for multiple-monitor systems as it allows the transfer of one monitor’s setup and adjustment data to another.


Various Markers
The OBM series can display various markers, including aspect markers, area markers, and center markers. In addition, the detailed display settings of each marker is allowed. For example, the color, brightness, horizontal/vertical position and thickness of aspect markers can be adjusted.
Custom Marker allows users to place lines on all four sides as they wish.


HDR / Camera Log Comparison
The unique function allows users to compare HDR and Camera Log by displaying them side by side.


Gamut Error
The total range of the SDI 10bit signal is 0 to 1023. The ranges 0 to 3 and 1020 to 1023 are the reserved values for Sync, and the total video signal range is 4 to 1019.
In a video signal, each primary component should lie between 0 and 100% of the video range between black level and peak level (R and G and B).
Ideally, video levels should lie within the specified limits so that programs can be distributed without adjustment.

100% White pattern : Y – 940, Cb – 512, Cr – 512
0% Black pattern : Y – 64, Cb – 512, Cr – 512
Expected Video Range : 64 to 940

In practice, it is difficult to avoid generating signals slightly out of range and it is considered reasonable to allow a small tolerance. Therefore, the EBU recommends that the RGB components and the corresponding Luminance (Y) signal should not exceed the “preferred minimum/maximum” range of digital sample levels in the table above.

Type 1: Black Zebra
When the targeted color space is selected as BT.709, the pixels outside of the targeted color space are displayed as Black Zebra.
The pixels over Y Maximum, Chroma Maximum, RGB Maximum are displayed as Black Zebra, and the pixels below Y Minimum, Chroma Minimum, RGB Minimum are also displayed as Black Zebra.

Type 2: Black & White Zebra
When the targeted color space is selected as BT.709, the pixels outside of the targeted color space are displayed as Black or White Zebra. The pixels over Y Maximum, Chroma Maximum, RGB Maximum are displayed as Black Zebra, and the pixels below Y Minimum, Chroma Minimum, RGB Minimum are displayed as White Zebra.

Type 3: Mono
When the targeted color space is selected as BT.709, the pixels inside of the targeted color space are displayed as Mono, and the pixels outside of the targeted color space are displayed as the color. In this type, black and white area is not recognized.


HDR Waveform
When HDR mode is set on, HDR Waveform is displayed on the screen.


In-Monitor Display(IMD)
The image source names and tally information can be displayed on the screen with an external remote function via Ethernet. The TSL system protocol is supported. The color of the source name and tally color can be selected from the following colors:  White, Red, Green, Blue, Yellow, Cyan and Magenta.


Password Lock for User Preset
When multiple users share the same monitor, each user can register his/her own password for color temperature and user preset data. This ensures the users correctly recall their preset data, and keep preset information safe from unauthorized use.


Custom 3D LUT File Import
The OBM series allows usesr to import 3D Look-up Table for accurate and consistent color matching between individual displays as well as using customized ‘looks’ that have been created by 3rd party color-grading applications. 32ˆ³, 33ˆ³, 64ˆ³ and 65ˆ³ cube file are supported.

* Specifications may be changed without notice.

Close Panel