Accurate Color Reproduction with Wide Color Gamut
The OBM-N170G provides industry-leading wide color gamuts. This monitor complies with the DCI-P3 color space with gamut ratio 108% and gamut coverage 99.5%, ensuring that the colors are reproduced according to industry standards.


Camera Log Selection
The OBM series has ab integrated camera LUT of various camera manufacturers. It allows users to load the following camera logs:
Log-C, C-Log / S-Log2 and S-Log3 / J-Log1. More camera LUTs will be updated.


Gamut Error
The total range of the SDI 10bit signal is from 0 to 1023. The ranges to 3 and 1020 to 1023 are the reserved values for Sync, so the total video signal range is from 4 to 1019.
In a video signal, each primary component should lie between 0 and 100% of the video range between black level and peak level (R and G and B).
Ideally, video levels should lie within the specified limits so programs can be distributed without adjustment.

100% White pattern : Y – 940, Cb – 512, Cr – 512
0% Black pattern : Y – 64, Cb – 512, Cr – 512
Expected Video Range : 64 to 940

In practice, avoiding the generation of signals slightly out of range is challenging, hence an allowance of a small tolerance is considered reasonable, Therefore, the EBU recommends that the RGB components and the corresponding Luminance (Y) signal should not exceed the “preferred minimum/maximum” range of digital sample levels in the table above.

Type 1: Black Zebra
When the targeted color space is selected as BT.709, the pixels outside of the targeted color space are displayed as Black Zebra.
The pixels over Y Maximum, Chroma Maximum, RGB Maximum are displayed as Black Zebra, and the pixels below Y Minimum, Chroma Minimum, RGB Minimum are also displayed as Black Zebra.

Type 2: Black & White Zebra
When the targeted color space is selected as BT.709, the pixels outside of the targeted color space are displayed as Black or White Zebra. The pixels over Y Maximum, Chroma Maximum, RGB Maximum are displayed as Black Zebra, and the pixels below Y Minimum, Chroma Minimum, RGB Minimum are displayed as White Zebra.

Type 3: Mono
When the targeted color space is selected as BT.709, the pixels inside of the targeted color space are displayed as Mono, and the pixels outside of the targeted color space are displayed as the color. In this type, black and white area is not recognized.


False Color
This function evaluates the Luma(Y’) level of the input image. If the certain Y’ level is set, the pixels with the designated Luma(Y’) level are displayed with the zebra pattern or the color pattern. There are three modes in OBM False Color.


Fast Mode
This function minimizes the interlaced video processing time delay and is also useful when displaying fast-motion interlaced video content and reducing the delay between video and audio.

Internal Video Processing Time


Focus Assist
This function controls the aperture level of a video signal and displays images with sharpened edges to help camera focus operations.


High Dynamic Range(HDR) Display
The OBM series supports display of High Dynamic Range footage.
Postium HDR function allows users to view both highlights and shadow details of scenes at the same time, resulting in more natural and realistic images.
The OBM series supports PQ EOTF (SMPTE ST 2084), Hybrid Log Gamma and S-Log3.

OBM-HDR displays both HDR and SDR(Standard Dynamic Range) versions of the image simultaneously for comparison.


Various Markers
The OBM series can display various markers, including aspect marker, area marker, and center marker. In addition, the detailed display settings of each marker are allowed. For example, the color, brightness, horizontal/vertical position, and thickness of aspect markers can all be adjusted.
Custom Marker allows the users to place top, bottom, left and right marker lines as they wish.


Adjustable Gamma
Gamma value can be adjusted from 1.0 to 3.0 based on the user’s preference to monitor the dark areas of the image.
Be it in light or dark environments, pictures taken can be easily viewed and analyzed.


Camera Log Mapped SDI Loopout
This function allows the loading of the camera log to the original image so the camera log mapped image can be sent to another monitor through an SDI loop out afterward.


Remote Control via Ethernet
The OBM series can be connected via Ethernet connection and controlled remotely through the network.


Waveform & Vector Scope Position Changeable
Users have the option of choosing which corner of the frame they would like to position the Waveform and Vectro Scope as this function is available on this series of monitors. 


System Data Copy
This function allows users to save the monitor configuration and adjustment settings on the USB memory stick and load them to other monitors. This is useful for multiple monitor systems, allowing the transfer of one monitor’s setup and adjustment data to another.


HDR Waveform
When HDR more is set on, HDR Waveform is displayed on screen.


In-Monitor Display(IMD)
The image source names and tally information can be displayed on the screen, with an external remote function via Ethernet. The TSL system protocol is supported. The color of the source name and tally color can be selectable among White, Red, Green, Blue, Yellow, Cyan, Magenta.


Password Lock for User Preset
When multiple users share the same monitor, each user can register his/her own password for color temperature and user preset data. This ensures the users correctly recall their preset data, and keep preset information safe from unauthorized use.


Custom 3D LUT File Import
The OBM series allow the user to import 3D Look-up Table for accurate and consistent color matching between individual displays as well as using customized ‘looks’ that have been created by 3rd party color-grading applications. 32ˆ³, 33ˆ³, 64ˆ³ and 65ˆ³ cube files are all supported.


Closed Caption
The OBM series can display closed captions with an SDI input. It supports the CEA-708(HD-SDI closed captioning standard) and CEA-608(SD-SDI closed captioning standard).

Accurate Color Reproduction with Wide Color Gamut
The OBM-N240G provides industry-leading wide color gamuts. This monitor complies with the DCI-P3 color space with a gamut ratio of 113.02% and a gamut coverage of 98.24%. This ensures that the colors are reproduced according to industry standards.


Camera Log Selection
The OBM series has an integrated camera LUT of various camera manufacturers. It allows users to load the following camera logs:
Log-C, C-Log / S-Log2 and S-Log3 / J-Log1. More camera LUTs will be updated.


Gamut Error
The total range of the SDI 10bit signal is 0 to 1023. The range 0 to 3 and 1020 to 1023 are the reserved values for Sync, and the total video signal range is 4 to 1019.
In a video signal, each primary component should lie between 0 and 100% of the video range between black level and peak level (R and G and B).
Ideally, video levels should lie within the specified limits so that programs can be distributed without adjustment.

100% White pattern : Y – 940, Cb – 512, Cr – 512
0% Black pattern : Y – 64, Cb – 512, Cr – 512
Expected Video Range : 64 to 940

In practice, it is difficult to avoid generating signals slightly out of range, so an allowance of a small tolerance is considered reasonable. Therefore, the EBU recommends that the RGB components and the corresponding Luminance (Y) signal should not  exceed the “preferred minimum/maximum” range of digital sample levels in the table above.

Type 1: Black Zebra
When the targeted color space is selected as BT.709, the pixels outside of the targeted color space are displayed as Black Zebra.
The pixels over Y Maximum, Chroma Maximum, RGB Maximum are displayed as Black Zebra, and the pixels below Y Minimum, Chroma Minimum, RGB Minimum are also displayed as Black Zebra.

Type 2: Black & White Zebra
When the targeted color space is selected as BT.709, the pixels outside of the targeted color space are displayed as Black or White Zebra. The pixels over Y Maximum, Chroma Maximum, RGB Maximum are displayed as Black Zebra, and the pixels below Y Minimum, Chroma Minimum, RGB Minimum are displayed as White Zebra.

Type 3: Mono
When the targeted color space is selected as BT.709, the pixels inside of the targeted color space are displayed as Mono, and the pixels outside of the targeted color space are displayed as the color. In this type, black and white area is not recognized.


False Color
This function evaluates the Luma(Y’) level of the input image. If the certain Y’ level is set, the pixels with the designated Luma(Y’) level are displayed with the zebra pattern or the color pattern. Below are three modes in OBM False Color.


Fast Mode
This function minimizes the interlaced video processing time delay and is also useful when displaying fast-motion interlaced video content and when reducing delay between video and audio.

Internal Video Processing Time


Focus Assist
This function controls the aperture level of a video signal and displays images on screen with sharpened edges to aid in camera focus operations.


High Dynamic Range(HDR) Display
The OBM series supports display of High Dynamic Range footage.
Postium HDR function allows users to view both highlights and shadow details of scenes at the same time, resulting in more natural and realistic images.
The OBM series supports PQ EOTF (SMPTE ST 2084), Hybrid Log Gamma and S-Log3.

OBM-HDR displays both HDR and SDR(Standard Dynamic Range) versions of the image simultaneously for comparison.


Various Markers
The OBM series can display various markers, including aspect markers, area markers and center markers. In addition, a detailed display settings of each marker is available. For example, the color, brightness, horizontal/vertical position and thickness of aspect markers can all be adjusted.
Custom Marker allows users to place top, bottom, left and right marker lines where they desire.


Adjustable Gamma
Gamma value can be adjusted from 1.0 to 3.0 based on the user’s preference to monitor the dark areas of the picture.
Whether taken in a dark or bright environment, the picture can easily be analysed and viewed.


Camera Log Mapped SDI Loopout
This function allows loading of the camera log to the original image so the camera log mapped image can be sent to another monitor through an SDI loop out afterward.


Remote Control via Ethernet
The OBM series can be connected via Ethernet connection and controlled remotely through a network.


Waveform & Vector Scope Position Changeable
Users have the option of choosing which corner of the screen they would like the Waveform and Vectro Scope to be positioned.


System Data Copy
This function allows users to save their monitor’s configuration and adjustment settings on a USB memory stick and load them onto other monitors. This is useful for multiple-monitor systems as it allowing the transfer of one monitor’s setup and adjustment data to another.


HDR Waveform
When HDR mode is on, HDR Waveform is displayed on the screen.


In-Monitor Display(IMD)
The image source names and tally information can be displayed on the screen with an external remote function via Ethernet. The TSL system protocol is supported. Users can select the color of the source name and tally color from the following colors: White, Red, Green, Blue, Yellow, Cyan and Magenta.


Password Lock for User Preset
When multiple users share the same monitor, each user can set his/her own password for color temperature and user preset data. This ensures that users can access their preset data while keeping their preset information safe from unauthorized use.


Custom 3D LUT File Import
The OBM series allows users to import 3D Look-up Tables for accurate and consistent color matching across multiple individual displays as well as using customized ‘looks’ that have been created by 3rd party color-grading applications. 32ˆ³, 33ˆ³, 64ˆ³ and 65ˆ³ cube files are all supported.


Closed Caption
The OBM series can display closed captions with an SDI input. It supports the CEA-708(HD-SDI closed captioning standard) and CEA-608(SD-SDI closed captioning standard)

* Specifications may be changed without notice.

* Specifications may be changed without notice.